Safety ChecklistSimple steps to a better garage door

Safety ChecklistSimple steps to a better garage door
By Duffy Dietz
According to recent statistics, auto accidents happen within five miles of home. Yet, what is often overlooked is the place where you park your car. Worn, malfunctioning or improperly installed garage doors and openers have killed many children. A simple inspection can guarantee a quieter, longerlasting overhead door and keep your customers safe.
Contact Reversal Test
Many injuries, especially to children, occur when a closing door failed to stop and reverse direction upon contact. This is usually because the down force settings are too high. The down force setting is a knob on the back of the opener that typically has an adjustment range of one through nine. It should be noted that not all devices that open and close the garage door are necessarily safe. Some old openers are equipped with a mechanism that only stops the door from closing when it strikes an object, not reversing the door in the process.
When checking for proper down force, a simple test for contact reversal should be completed. Begin with the door fully open and attached to the opener. Under the center of the door, place a 1 1/2-inch thick piece of wood, such as a 2-by-4, flat on the floor. Electric openers should reverse the door upon hitting the wood with minimum pressure.
If the door does not reverse, decrease the down force by turning the control counterclockwise. Make adjustments in small increments until the door reverses normally. After each adjustment, run the opener through a complete cycle. If the door reverses during the closing, increase the down force by turning the control clockwise.
Make small adjustments until the door completes a close cycle. After each adjustment, run the opener through a complete travel cycle. Do not increase the force beyond the minimum amount required to close the door.
Checking Open Force
Just as there is a force to go down, there is a force to raise the door. Grasp the door bottom when the door is about halfway through open travel. The door should stop. If the door is hard to hold or doesn’t stop, decrease the open force by turning the control counterclockwise.
Make small adjustments until the door stops easily and opens completely. After each adjustment, run the opener through a complete travel cycle. Do not increase the force beyond the minimum amount required to close the door.
If the door does not open at least 5 feet, increase the open force by turning the control clockwise. Make small adjustments until the door opens completely.
After each adjustment, run the opener through a complete travel cycle. Do not increase the force beyond the minimum amount required to close the door.
Prior to 1982, openers had devices intended to reverse the closing door when it strikes an object, but for reasons related to age, installation and maintenance, these products may not be safe enough to prevent child entrapment.
Photoelectric Eyes
Here are two simple tests to determine if the electronic eyes are installed and functioning properly. The noncontact reversal test begins with the door fully open. Standing just outside the path of the door and using the transmitter, push the button to close the door. Wave an object across the path of the photoelectric eye beam as the door is closing. The door MUST reverse and return to the fully open position to pass this test.
Checking for proper location of the photoelectronic eyes is perhaps the simplest test. If present, the device must be mounted at a maximum of 6 inches above the floor to detect an obstruction in the path of the door. Using a tape measure, confirm the device is no higher than 6 inches above the floor or make adjustments if needed. To ensure safety, the wallmounted control should be positioned at a minimum height of 5 feet.
A properly maintained garage will not only provide your customers with years of service, but will also ensure their safety.

Child dies under garage door.....

Another Child Dies Under Garage Door: Are We Doing Enough to Educate?07/21/2008 14:24
Last week, Terry Lee Barnett was killed when his family’s garage door fell and pinned him by the neck at his Indianapolis home, several papers reported July 18.In May, I blogged about theOntario boy that was killed in a similar fashion – albeit under very different circumstances. In the Canadian case, a construction company was on-site and working on the garage when the incident occurred. Disturbingly, the circumstances in Indianapolis were as follows (according to the local news story):
Police said the teen was fatally injured about 11 a.m. when a two-by-four dislodged from the garage door it had been propping open at his home... Terry was pinned beneath the door of the detached garage, which is behind the family's home.
Kitty Barnett [the victim's mother] said the electric motor that raises and lowers the door went out Wednesday night. She said the landlord had recently fixed the door, and she does not believe the accident was the result of negligence on the part of the home's owner.
The broken garage door did not appear to violate any city or county regulations, according to spokesmen for the Department of Metropolitan Development and the Department of Health.
There seems to be information missing from this story...or at least, I hope so. I hope propping open a garage door with a two-by-four is not what the mother means when she says her landlord fixed it.
I can't speculate on the circumstances, but I'm left with questions (and I'm sure I'm not the only one). I’d like to hear your thoughts on and reactions to this news. Drop me a line at lvasquez@vpico.com.